Gallien krueger backline 115 combo Pc#
Gallien krueger backline 115 combo series#

Strat™, Stratocaster™, Esquire™, Telecaster™, Tele™, Jazzmaster™, Jaguar™, Mustang™, P.Bass™, J.Bass™ and Fender™ are registered trademarks of Fender™ Musical Instruments. Standard NEMA 5-15 plug for North American use at 110-120 Volts AC. 10 Ft Length Give Extraįlexibility In Equipment Placement, Reduces Use Of Extension Cords. Many Guitar Amps, Power Amps, Effects Units, Etc. Revisit™ 10 ft POWER CORD, DETACHABLE, 3-WIRE, 18ga, 10įt LONG, IEC CONNECTOR AT EQUIPMENT END. Standard NEMA 5-15 plugįor North American use at 110-120 Volts AC. Guitar amps, power amps, effects units, etc. Revisit™ 6 ft POWER CORD, DETACHABLE, 3-WIRE, 18ga, 6 ft LONG, IECĬONNECTOR AT EQUIPMENT END. Includes 3 black oxide coarse-thread mounting screws, #6x3/4'. Hole is 3/8', for most Switchcraft type jacks. Works well with the Switchcraft J-11 1/4' jacks Similar in style to vintage Fender™ jack plates. JACK PLATE, BLACK METAL, SINGLE 1/4' JACK, 2' OUTSIDE DIAMETER. This is a tough, durable 1.2mm Black Oxide SteelĪlso included are four #8 x 3/4' black mounting screws. Does NOT fit the SW-650, SW-701, or SW-206 switches Does NOT fit the TSL/DSL amps in the JCM2000 Is smaller than the original round switch cap from Marshall™ found on some of Round caps used on the Gallien-Krueger 400RB-II, 700RB-II, 1001RB and similar models.įits push switches with actuator shaft of 2.7mm square. This is a black 5mm (approx 3/16') diameter X 9mm long switch cap which fits the SW-212Īnd 090-0012-0 Push Switches. Original Fender™ part number 0028104000.Īlso fits the Gallien-Krueger MB150E amp. Used on channel control and drive boost switches on theįront panel of the Fender™ Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe, Bluesĭeville, Blues Junior. See either the K-212 or the K-058, depending on the amplifier model. Original Gallien-Krueger part number 090-0012-0. The front panel of the 400RB-II, 400RB-III, 400RB-IV, 700RB-II, 1001RB-II, the MicroBass Series, Backline 110, Backline 112, Backline 115, Backline 210,Īnd Backline 350 G-K amps. Includes nut and washer.Ħ electrical terminals on bottom of switch (DPDT). Same as the J-12A jack, but with longer (3/8') threaded bushing for mounting in thicker panels. (SHORTING), WIRED, Switchcraft ™, LONG BUSHING JACK, 1/4', MONO, CLOSED CIRCUIT (SHORTING), WIRED, Switchcraft ™įound in vintage Fender ™ (and other) amps as the input jack.Īlso used in the Hot Rod Deluxe/Deville, Blues Deluxe/Deville as the main JACK, 1/4', MONO, OPEN CIRCUIT, WIRED, Switchcraft ™įound in many guitars, effects pedals, amps speaker output.

Genuine Switchcraft™ nut and washer set for the J-563 jack. Reuse existing nut or order nut separately as part #JNUT-38, Nut & Washer NOT included - reuse original, or order JNUT-38.Īnd Gallien-Krueger ™. Models (including the G-K Backline 210 and some of the G-K RB series, such as

Gallien krueger backline 115 combo Pc#

JACK, 1/4', MONO 4-PIN, PC MOUNT, Gallien-Krueger ™ AMPS Order the PNW-16 nut found in this section) Life, and help prevent 'scratchy pots' in later life.ĭownload cross-reference guide for these pots. The dust caps seal out dust for reliability, longer These pots areĪvailable with optional dust caps installed. Diameter of the body of the pot is slightly smaller than a dime. Note: These pots do not fit all G-K amps.Ĭompare carefully with the photo, or inquire if unsure.

Gallien krueger backline 115 combo series#

PC board circuitry, including the 700RB, 800RB and 1000RB (original series from the

Used in many Gallien-Krueger ™ amp models with PC MOUNT, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING 'break-through' and adds overall durability. Ideal for amp heads, combo amps, or smaller speaker cabinets. (wide end) x 3/4' diameter (narrow end) x 0.85' tall. Ideal for rack-mount amps, combo amps, or small speaker cabinets. MEDIUM BLACK TAPERED RUBBER FEET, SET OF 4. The integral metal washer in the mounting hole helps prevent mounting screw Ideal for large rack cabinets or speaker cabinets. This heavy-duty rubber foot offers a sure grip With built-in lock washer to keep the screwĪnd nut from loosening. Used to connect a ground wire to a screw and nut on a chassis. Made from tin-plated brass - will not rust.